Safety Data Sheet - Stabilant 22A (TM) -
by.- D.W. ELECTROCHEMICALS LTD
Newkirk Road North, (Unit 3)
Hill, Ontario L4C 3G4
- Fax: (905)
FIRE HAZARD SOME HEALTH HAZARD
(WHMIS Classification B-2,
- Name: Stabilant 22A - (No synonyms
Use: Electronic Contact Enhancer
75% Alcohol - 25% Polyglycol
Family Name & Identity
Isopropanol [Fire & Some Health Hazard - CAS 67-63-0]-25% Stabilant 22 -[No Fire or Health Hazard] - falls under
CAS 9003-11-6 (a Modified Polyoxypropylene-Polyoxyethylene
Block Polymer of the, Polyglycol Family
Thin clear liquid
Sharp alcohol odor
Threshold: No Data
Point: -89º Celsius
Point: 82.4º Celsius
Temp: No Tests Run
in water: >500 grams/liter
No Tests Run
Pressure(mm): 33 mmHg @ 20º Celsius
Rate: No Tests Run
Index: No Tests Run
of Water/oil distribution: No Tests Run
- VOC: 75
FIRE & EXPLOSION HAZARDS
Explosion Limit (% by Volume): 12.0
Explosion Limit (% by Volume): 2.0
Temperature: 399º Celsius
Point [Method]: 13 º Celsius [Tag C.C.]
- Hazardous Combustion
Products: No Data
Media: Water fog, C02, Foam, Dry Chemical
Procedures: Do not use direct water stream
as this could spread the fire. Self-Contained Breathing Apparatus should
be used when fighting a fire in a confined area or when exposed to
Data - Sensitivity to impact: No Tests Run
to Static Discharge: No Tests Run
Fire & Explosion Hazards: Improperly Disposed of Stabilant soaked combustible materials might be
subject to spontaneous combustion. Heat may build internal pressure in
container, leading to rupture of container.
HEALTH EFFECTS DATA
the material is 75% isopropanol it exhibits all of the health hazards of
isopropanol but to a lesser degree. The lower concentration of the
isopropanol mitigates the defatting and drying effects of the near
absolute alcohol's on the skin although there is still a hazard on eye
contact. If the container of Stabilant 22A is
left uncapped for extended periods at normal room temperatures, the
isopropanol will evaporate reducing the hazards somewhat. When applied to
contacts the isopropanol will evaporate leaving the nonvolatile portion of
the material (Stabilant 22) on the surfaces, and
reference should be made to the MSDS for Stabilant
22 as to the potential hazards of that product.
(oral, rat): 5000 mg/kg.
irritation: LD 50
(skin, rabbit 12800 mg/Kg.) The material is a mild irritant and may
cause defatting and drying of the skin.
Skin Exposure: Prolonged and repeated contact
may cause dermatitis.
- First Aid
on Skin Exposure: Major spills on clothing
require removal of contaminated clothing, then flush area with running
water and wash with soap and water. Small area contact, wash with running
water, then soap and water. Obtain medical advice.
irritation: The vapor is a mild irritant
which may cause conjunctivitis and corneal damage. The liquid is a severe
eye irritant which may cause permanent eye damage.
- First Aid
on Eye Exposure: Flush eyes with running water
for at least 20 minutes holding eyelids open. Obtain medical attention
immediately! Treat for isopropanol exposure.
when Inhaled: LC50 (inhalation, rat , 16000ppm/8H) May cause irritation of the eyes, nose
and throat and of the respiratory tract. Overexposure could cause Central
Nervous System Depression characterized by headache, dizziness,
drowsiness, nausea, vomiting, abdominal pain and incoordination. Severe
overexposure could lead to coma and possibly death due to respiratory
failure. Remove to fresh air. If not breathing give artificial
respiration. Obtain medical attention immediately.
- First Aid
oral ingestion: If victim is alert and not
convulsing, rinse out mouth and give 1/2 to 1 glass of water to dilute
material. DO NOT induce vomiting. If spontaneous vomiting occurs, have
victim lean forward with head down to avoid breathing in of vomitus, rinse
mouth and administer more water--Transport victim to an emergency
Medical Care: Extreme care must be taken to
avoid aspiration of product into lungs, which may result in pulmonary
Limits: No Tests Run
to Material: Limited tests indicate no
Effects: No Tests Run.
No Tests Run.
No Tests Run.
Materials: None Known.
under normal conditions: Stable
under fire conditions: Flammable
to avoid: Excessive Temperatures,
sparks, open flames and all other sources of ignition.
Strong oxidizers, also may react with aluminum at high temperatures
Decomposition Products: CO, C02
Polymerization or Reactivity: Avoid oxidizing materials. Can
react violently with potassium oxides and potassium. Can ignite in contact
with platinum black catalyst.
No Tests Run - No Data
Toxicity: Harmful to aquatic life at low
concentrations. No quantitative data known.
Inhibition in Influent: No Data
ENGINEERING CONTROLS & SPECIAL PROTECTION INFORMATION
Note: Conditions of use, adequacy of
engineering or of other control measures and actual exposure will dictate the
need for specific protective devices at the workplace. The recommendations
listed in this section indicate the type of equipment which will prevent
overexposure to the product.
Where the material is being applied by swab or small
brush, or from a dropper bottle, it is highly unlikely that sufficient air
concentration of the isopropanol could occur under normal ventilation such
that a health hazard could be created. Whenever large volumes of the
material are being used (>250 mL) or whenever the continually exposed
surface area of the material is in excess of 3 Square ft., it is suggested
that local exhaust ventilation be provided.
Protection: Where small amounts are being
used with a swab or small brush, or are being dispensed from a dropper
bottle, respiratory protection is not needed under normal ventilation
conditions. Where large volumes of the material (>250 mL) are being
used or where large surface areas are being exposed (e.g. - dipping tanks)
the use of a NIOSH/MSHA approved air purifying respirator equipped with
organic vapor cartridges be used if exposed to concentrations up to 1000
ppm. Use an air supplied unit if exposed to higher or unknown
concentrations. (Such as in bulk handling)
or Neoprene gloves should be worn when the handling of circuit boards or
connectors requires constant skin contact with the material.
Protection: Goggles or Face shield when
there is a potential for eye contact.
Non slip when handling bulk amounts.
Rubber or Neoprene protective clothing when handling bulk amounts
Handling: Ground equipment to prevent
static discharge accumulation Observe physical safety procedures
commensurate with the size of the container involved.
SPECIAL STORAGE PRECAUTIONS
Procedures: Store in a cool, dry, well
ventilated location away from strong oxidizers.
SPECIAL SHIPPING DESCRIPTION (Under the TDG Act)
Name: Stabilant 22A - Isopropanol
NOTE.- As 75% of material is Isopropanol, the material should be treated
as Isopropanol for shipment using:
(Product ID#) UN1219--Packing Group - II—Class: 3
OTHER REGULATORY INFORMATION
States Customs: The quantity
of materials in this product have been reviewed and are not
reportable under SARA title III.
(These materials sre listed on the TSCA Inventory)
OSHA (29CFR1900.1200) Classification:
Flammable Liquid, Eye Irritant
These materials are listed in the Domestic Substance
List under the CEPA.
- NCSL not listed
For tariff purposes the material is classified as Semiconductor,
Other. Harmonized Tariff Code 8541.50.00.80
FIRST AID - EMERGENCY
Flush eyes with running water for at least 20 minutes holding eyelids
open. Obtain medical attention immediately! Treat for isopropanol
Wash with soap and water. Remove and launder contaminated clothing before
re-use. Consult a physician if irritation develops at site of exposure.
If victim is alert and not convulsing, rinse out mouth and give 1/2 to 1
glass of water to dilute material.
- DO NOT
spontaneous vomiting occurs, have victim lean forward with head down to
avoid breathing in of vomitus, rinse mouth and administer more water.
victim to an emergency facility IMMEDIATELY!
Remove to fresh air. If not breathing give artificial respiration. Obtain
medical attention immediately.
of Leaks & Spills: Eliminate all sources of
ignition. Stop or reduce discharge if safe to do so. Prevent from entering
water courses or sewers. Ventilate enclosed spaces. Contain by applying
absorbent. Collect waste absorbent for disposal. For significant releases
contact regulatory authorities.
Chemicals: None known.
of Waste: Dispose of waste materials in
an approved incinerator or waste treatment/disposal facility in accordance
with applicable regulations. Do not dispose of in sewer or with normal
OTHER DATA (Excluded from waiver at end of MSDS)
Metals: D.W. Electrochemicals Ltd. has
a policy of not allowing any intentional addition of any heavy metals,
such as lead, cadmium, mercury, or hexavalent chromium, or their
compounds, to be used in inks or in the labels on our packaging and
requires the total concentration of these materials, if present, to be so
at a level of less than 100 parts per million and we so certify.
Legislation Article 4(1) pertaining to Heavy Metals in Stabilants
and other prohibited components: D.W.
Electrochemicals Ltd. has a policy of not allowing any addition of any
heavy metals, such as lead, cadmium, mercury, or hexavalent chromium, or
their compounds, to be used in the Stabilants
and requires the total concentration of these materials, if present, to be
so at a level of less than 100 parts per million and we so certify. Nor
does Stabilant contain any polybrominated
biphenyls (PBBs) or polybrominated diphenyl ethers (PBDEs) and we so certify.
Depleting Chemicals: Because of our corporate
opposition to the use of ODC's either in the manufacture of, or as an
inclusion in any of our products, D.W. Electrochemicals Ltd. has
consistently refused to provide any of our products in aerosol spray
packaging and/or to supply any of our materials diluted with any Class 1
ODC, and we so certify.
We certify that this material has been subjected to tests capable of
detecting PCB's to a level of less than 2 parts per million and no PCB's
have been found.
New standards are in place in an attempt to reduce the amount of plastics,
tape and/or adhesives used and to ensure that our packaging may be reused
MSDS PREPARATION DATA & EMERGENCY PHONE NUMBER
By: Wm Wright
Date: December 31st, 2011
Revision: Revision 23 Updated, and
for inclusion on the web page
Phone: (905) 508-7500
Canada 1987, US Patent 4696832. Others Pending.
Stabilants, and the term "Contact Enhancer"
© Copyrighted 1983.
NATO/CAGE Supplier code
15 mL Stabilant
22A has NATO Stock Number 5999-21-900-6937
Electrochemicals Ltd. urges each customer or recipient of this MSDS to study it
carefully to become aware of/and understand the hazards associated with the
product. The reader should consider consulting reference works or individuals
who are experts in ventilation, toxicology or fire prevention, as necessary or
appropriate to use and understand the data contains in this MSDS.
safe use and handling of this product, each customer or recipient should (1)
notify employees, agents, contractors and others who may use this material, of
the information in this MSDS and any other information regarding hazards or
safety, (2) Furnish this same information to each customer for the product, and
(3) request customers to notify their employees customers, and other users of
the product of this information.
information and recommendations contained herein are based on data believed to
be correct, however no guarantee or warranty of any kind, expressed or implied,
is made with respect to information and recommendations contained herein except
Please refer to Technical Note 1 -
MSDS for Stabilant 22
OF MSDS's AND NOTES
OF TECHNICAL NOTE 4